Husqvarna 570 AT Workshop Manual Download

Page: 35 / 58

CARBURETTOR

English – 35

WARNING!.

Never.direct.the.compressed.air.jet.towards.

the.body..Air.can.penetrate.into.the.blood.

circulation,.which.means.mortal.danger.

WARNING!.

Fuel.has.the.following.hazardous.properties:

1..The.fluid.and.its.fumes.are.poisonous.

2..Can.cause.skin.irritation.

3..Is.highly.inflammable.

Cleaning.and.inspection

Clean all units in clean petrol.

Use compressed air to dry the petrol on the components.

Direct the air through all channels in the carburettor

housing and make sure that they are not blocked.

See fig. 10, 11 and 12 and check the following:

1. That gaskets, pump and control diaphragms are

undamaged.

2. That there is no play on the throttle and choke valve

shafts.

3. The needle valves and lever are not worn at C and D in

fig. 10.

4. The fuel filter is undamaged. See L in fig. 11.

5. The tips of the high and low speed screws are not

damaged.

6. The intake manifold is undamaged. See page

The carburettor has an extra air shutter connected in

parallel with the ordinary throttle valve. The valve housing

with axle is secured in the carburettor using two screws.

The gasket between the carburettor and the valve

housing is, if the saw has the designation XPG, replaced

by a carburettor heater.

Fig. 13

Fig. 12

Zama C1M-EL40

Zama C1M-EL28

Summary of Contents for 570 AT



























































Search results

Summary of Contents for 570 AT

Reviews:

Related manuals for 570 AT

Brands by name

Popular brands

Husqvarna 570 AT, Workshop Manual

Search results

Summary of Contents for 570 AT

Reviews:

Related manuals for 570 AT

Brands by name

Popular brands