manualshive.com logo in svg

Husqvarna 570 AT, Workshop Manual, Page: 27 / 58

Share
Download
Husqvarna 570 AT Workshop Manual Download Page 27

CENTRIFUGAL.CLUTCH

English – 27 

Centrifugal.clutch

Dismantling

When dismantling the centrifugal clutch the chain brake 

must be in the off position.

1.  Remove the cylinder cover, chain and bar. See  

  Operator's Manual.

2.  Remove the chain guide plate by unscrewing the  

  bolt (A). See fig. 1.

3.  Remove the locking ring (B) with washer and lift  

  up the clutch drum (C) with needle bearing (D) and  

  chain drive sprocket (E). See fig. 2.

4.  Remove the spark plug and fit the piston stop.  

  Remove the clutch with the clutch tool. 

  Note! Left-hand thread. Screw in the direction of the  

  arrow as shown in fig. 3.

The following steps (5-6) describe the dismantling of 

clutch.

5.  Stretch out the springs with circlip pliers and press  

  them out from the clutch hub.

6.  A complete clutch or springs are available as spare  

  parts.

 Fig. 1

 Fig. 2

 Fig. 3

 Fig. 4

NOTE!.

The.clutch.springs.must.not.opened.more.

than.is.necessary..Risk.of.deformation.

A

A

B

E

D

C

Summary of Contents for 570 AT



























































Reviews:

No comments