Husqvarna 570 AT Workshop Manual Download

Page: 44 / 58

ANTI-VIBRATION.SYSTEM

44 – English

WARNING!.

The.fuel.used.in.the.chainsaw.has.the.

following.hazardous.properties:

1..The.fluid.and.its.fumes.are.poisonous.

2..Can.cause.skin.irritation.

3..Is.highly.inflammable.

Anti-vibration.system

Dismantling

1. Dismantle the following parts:

•

Chain and bar. See the Operator's Manual.

•

Cylinder cover. See the Operator's Manual.

•

Tank unit and front handle.

2. Remove the spring on the cylinder with a 4 mm Allen

key. See fig. 1.

3. Remove the springs on the tank unit with a 4 mm

Allen key. See fig. 2.

Cleaning.and.inspection

Clean and inspect all parts.

Assembly

1. Fit the springs on the cylinder and tank with a 4 mm

Allen key. See fig. 1 and fig. 2.

Note! Harder springs are available. Should only be

used together with longer guide bars. See IPL for part

number.

2. Assemble the following parts:

•

Tank unit and front handle. See page

•

Cylinder cover. See the Operator's Manual.

•

Chain and bar. See the Operator's Manual.

Fig. 1

Fig. 2

Summary of Contents for 570 AT



























































Search results

Summary of Contents for 570 AT

Reviews:

Related manuals for 570 AT

Brands by name

Popular brands

Husqvarna 570 AT, Workshop Manual

Search results

Summary of Contents for 570 AT

Reviews:

Related manuals for 570 AT

Brands by name

Popular brands