Husqvarna 570 AT Workshop Manual Download Page 43 | Manualshive

Page: 43 / 58

Husqvarna 570 AT Workshop Manual Download Page 43

TANK.UNIT

English – 43

Cleaning.and.inspection

Clean all parts and check that the fuel pipe is intact.

Assembly

1. If the chainsaw is fitted with hand grip heating, fit the

heating element if it has been removed.

See page

22

and

24

.

NOTE!.

Take.care.not.to.damage.the.fuel.pipe.and.

throttle.cable.

2. If the throttle lock has been removed, it should be

refitted before the tank unit and engine unit are

assembled. See page

17

.

3. Lift the engine unit over the tank unit and push the

fuel, tankvent pipe and throttle cable into their holes

in the bottom of the carburettor space.

4. Fit the bolts (E and H). See fig. 2. Tighten the bolts

to the torque in the service data, page

10 and 11

.

5. Fit front handle with the bolts (D, F and G). See

fig.

2

. Tighten the bolts to the torque in the service

data, page

10 and 11.

6. Fit the fuel pipe (B) on the carburettor and tankvent

pipe (C). See fig. 1.

7. Insert the throttle cable casing in the attachment and

hook on the throttle cable (A) on the carburettor.

See fig. 1.

8. Fit the cylinder cover, guide chain and bar.

See the Operator's Manual.

«
...
41
42
43
44
45
...
»

Summary of Contents for 570 AT



























































Reviews:

No comments