Husqvarna 570 AT Workshop Manual Download

Page: 22 / 58

22 – English

ELECTRICAL.SYSTEM

Hand.grips.and.carburettor.heater,.

576.XPG

Some chainsaws are fitted with hand grip heaters and

carburettor heaters, and consist of the following parts:

• Generator.

• Switch.

• Heating element in rear hand grip.

• Front hand grip with heating element.

• Carburettor heating element.

• Thermostat.

Trouble.shooting

Trouble shooting can be carried out with most

components fitted on the saw. Trouble shooting requires:

- ammeter

- ohmmeter

- cooling spray.

The most common fault is oxidisation of the heating

element contacts in the rear hand grip and the switch

contact.
Carry out trouble shooting as follows:

Heating.element.in.rear.hand.grip.

Separate the cable connection at C. See fig. 9.

Clean the contacts C and D. See fig. 9.

Measure the resistance between point C and D.

The resistance for heating elements should be 0,8-1,0 ohms.

Replace the element if the values deviate.

Front.hand.grip.with.heating.element

Measure the resistance in the front hand grip element

between points C and B. See fig. 9. The ohmmeter

should show 3-4 ohms.

If the value is higher, replace the hand grip.

Generator

Measure the resistance in the generator between the

points A and E. See fig. 9.

The ohmmeter should show 0,5 ohms.

If the value is higher, replace the generator.

Switch

Release one of the connections to the switch and

connect the ohmmeter between the points A and B.

See fig. 9.

The ohmmeter should show more than 1000 ohms with

the switch in position “0”.

The ohmmeter should show at least 0,1 ohms with the

switch in position “1”.

Replace the switch if the values deviate.

Carburettor.heating.element.and.thermostat

The heating element and thermostat are in a single unit

and must be replaced together.

Release the earth cable G. Measure with the ohmmeter

between G and F.

The ohmmeter should show 0 at an air temperature of

15 C or higher. Cool the thermostat with a cooling spray

or the like.

The ohmmeter should show 8 A.

Replace the two elements if the values deviate.

Refit the relevant components.

Fig. 9

Summary of Contents for 570 AT



























































Search results

Summary of Contents for 570 AT

Reviews:

Related manuals for 570 AT

Brands by name

Popular brands

Husqvarna 570 AT, Workshop Manual

Search results

Summary of Contents for 570 AT

Reviews:

Related manuals for 570 AT

Brands by name

Popular brands