Husqvarna 570 AT Workshop Manual Download | Manualshive

Page: 18 / 58

background image

STARTER

18 – English

WARNING!.

If.the.spring.is.tensioned.on.the.starter.

pulley.it.can.fly.up.and.cause.personal.

injury.

Wear.protective.glasses.

WARNING!.

If.the.spring.is.tensioned.on.the.starter.

pulley.it.can.fly.up.and.cause.personal.

injury.

Wear.protective.glasses.

Starter

Dismantling

!

Cleaning.and.inspection

Clean all components and check the following:

1. Starter cord.

2. The dogs on the starter pulley.

3. That the pawls on the flywheel are intact, spring

back towards the centre and move freely.

Fig. 1

Fig. 2

Fig. 3

!

4. Remove the central bolt (C) and take out the washer

and starter pulley (D). See fig. 3.

5. If the starter cord is to be replaced, cut it off pull out

the ends from the handle and starter pulley with

pointed pliers.

6. If the spring is to be replaced, remove the screws (E)

and the spring cassette (F).

A

B

E

F

D

C

1. Remove the four bolts holding the starter to the

crankcase and remove the starter. See fig. 1.

2. Pull out the handle 20-30 cm and take out the cord

from the slot in the starter pulley. See fig. 2.

3. Rotate the starter pulley anticlockwise until the ten

sion on the pulley is released.

«
...
16
17
18
19
20
...
»

Summary of Contents for 570 AT



























































Reviews:

No comments

Related manuals for 570 AT

Brand: TimberKing Pages: 32

Brand: Echo Pages: 192

Brand: Milwaukee Pages: 286

Brand: Yard force Pages: 19

Brand: Qualcast Pages: 16

Brand: Raider Pages: 48

Brand: Tanaka Pages: 20

Brand: Tanaka Pages: 68

Brand: GARDEO PRO Pages: 46

Brand: TCK Pages: 20

Brand: LawnMaster Pages: 40

Brand: Jonsered Pages: 15

CS 2152 EPA III

Brand: Jonsered Pages: 44

Motosierra GS2500

Brand: Greencut Pages: 78

Brand: Greencut Pages: 78

Brand: Greencut Pages: 80

Brand: Greencut Pages: 80

Brand: Greencut Pages: 84

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands