manualshive.com logo in svg

Hunter GSP9700 Series, Operation Instructions Manual

Share
Download
Hunter GSP9700 Series Operation Instructions Manual Download Page 77

Press the green “START” button if “Hood Autostart” is disabled. After wheel comes to 
a complete stop, raise safety hood. Place left plane weight (if in DYNAMIC mode) per 
the balance procedure being performed. Refer to “Balancing Procedures,” 

page 23

.

SPOKES OF WHEEL

SPOKE LOCATION SHOWN

POSITIONED AT DATASET

ARM HOLDER CONTACT

POINT WITH RIM

SERVO-AIDED ADHESIVE

WEIGHT PLACEMENT

Press the green “START” button with the safety hood in the RAISED position and the 

GSP9720JLR

 will servo to the location for the right adhesive weight plane (dynamic) 

or the static adhesive weight plane (static), aligned with the first spoke. With the 
servo enabled, attach the adhesive weight behind the first spoke using the weight 
amount shown on the LCD. Refer to “Servo-Aided Adhesive Weight Placement,” 

page 61

.

Press the green “START” button with the safety hood in the RAISED position and the 

GSP9720JLR

 will servo to the location for the second spoke. 

Attach the appropriate weight as displayed on the console. All weight plane displays 
should show “zero.” SPLIT SPOKE® balancing procedure is complete. 

Re-entering Similar Wheel after Split Spoke® is Enabled 

Once Split Spoke® mode is enabled, use the “Set New Spoke Location” key to input 
the spoke orientation of the other three rims from a set to avoid re-measuring the 
weight plane dimensions each time. This can be performed with or without the laser. 

GSP9720JLR Wheel Balancer Operation Instructions 

Balancing Procedures 

x

 69 

Summary of Contents for GSP9700 Series






























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands