Hunter GSP9700 Series Page 102 Operation Instructions Manual Download | Manualshive

Page: 102 / 157

background image

4.5 TranzSaver™

NOTE:

TranzSaver™ will only be displayed when the load roller is
enabled.

TranzSaver™ displays the diameter of the tire and wheel assembly on the balance
screen. Measuring overall tire diameter and comparing the diameter to other tires on
the same vehicle may be important for all-wheel drive and four-wheel drive vehicles
to ensure proper drive line performance and minimize the potential for premature
transmission transfer case failure.

Mismatched tires in varying diameters or using unequal inflation pressures for AWD
and 4WD vehicles may result in immediate drivability problems or premature
transmission transfer case failure. This necessitates that 4WD and AWD vehicles use
tires that are very closely matched in diameter and inflation pressures. Tire diameter
variations can be caused by using different sized tires, tires with different tread
designs, tires made by different manufacturers, different inflation pressures or even
tires worn to different tread depths.

Depending on the vehicle and manufacturer, AWD and 4WD drivetrains can vary
greatly in their sensitivity to unequal tire diameters. Consult the vehicle owner's
manual for vehicle manufacturer's recommendations when replacing less than four
tires. If 4x4 or AWD vehicles manufacturer's recommendations are not available, a
good ‘rule of thumb’ is that all tires should be within 0.30” diameter of each other.

IMPORTANT:

It is important to note that QuickMatch® and Road Force
Measurement® apply different forces to the tire. The
TranzSaver™ measurement will not be the identical if the
same tire and wheel assembly is compared between the
two. As a result, the tire diameters measured between these
two modes may differ.

In QuickMatch® mode, TranzSaver is a light load measure-
ment that does not take into account tire pressures. This is
an accurate method of computing tire height which is similar
to using an ‘unloaded’ tape measure form of measurement.

In Road Force Measurement® (high load measurement)
mode, TranzSaver is superior and offers a high load
measurement that also takes into account the tire pressures
and the change it will have on the tire when placed on the
vehicle.

94

x

Road Force® Measurement Procedures

GSP9720JLR Wheel Balancer Operation Instructions

«
...
100
101
102
103
104
...
»

Summary of Contents for GSP9700 Series






























































































































































Reviews:

No comments

Related manuals for GSP9700 Series

Brand: Snap-on Equipment Pages: 3

Brand: Snap-On Pages: 20

Brand: Snap-on Incorporated Pages: 28

Brand: Snap-on Incorporated Pages: 38

Brand: Snap-On Pages: 120

Brand: Snap-On Pages: 128

Brand: Snap-On Pages: 152

JohnBean B2000P Series

Brand: Snap-on Equipment Pages: 252

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands