manualshive.com logo in svg

Hunter GSP9700 Series, Operation Instructions Manual

Share
Download
Hunter GSP9700 Series Operation Instructions Manual Download Page 60

Press the green “START” button with the safety hood in the raised position and the 

GSP9720JLR

 will find the TDC for the right weight plane. 

Attach the weight amount shown on the LCD for the right weight plane to the outer 
rim of the wheel. 

NOTE: 

If optional HammerHead™ TCD weight locator is installed, 
the weight should be applied at the location marked by the 
laser.

Refer to “3.23 Optional HammerHead™ TDC Laser 

Adhesive Weight Locator,” on page 76.

If necessary, use the right “

” to split the weight. 

Refer to “Split Weight® 

Feature,” page 66.

Left and right weight plane displays should show “OK” after checkspin. 

STANDARD balancing procedure is complete. 

MIXED WEIGHTS Balancing Procedure  

Using a Combination of Clip-On & Adhesive Weights 

Verify that the wheel is clean and free of debris. 

Remove all previous weights. 

Mount tire/wheel assembly. 

Refer to “Mounting the Wheel on the Spindle Shaft,”  

page 25.

Press 

. Use the arrows to select “MIXED WEIGHTS BALANCE” and press 

“OK.”

Select either grams or ounces by rotating the control knob and highlighting either  
“g” or “oz.”  

Select “DYNAMIC” by rotating the control knob to highlight “ 

,” if SmartWeight is 

enabled. 

Refer to “Dynamic Balancing,” page 47.

52

x

 Balancing Procedures 

GSP9720JLR Wheel Balancer Operation Instructions 

Summary of Contents for GSP9700 Series






























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands