manualshive.com logo in svg

Hunter GSP9700 Series, Operation Instructions Manual

Share
Download
Hunter GSP9700 Series Operation Instructions Manual Download Page 117

The first statistics screen, shown above, represents spin counts for first harmonic 
results. Columns 3 and 4 show the larger runout amount of the two measured rim lips 
for each spin (the smaller values for each spin are not stored). Column 5 shows the 
radial average of the two rim lips. The rim average is used for Forcematching®, 
therefore use this column as an indicator of how much matchable rim runout was 
measured by the 

GSP9720JLR

 compared to how much tire (and assembly) road 

force was measured (columns 1 and 2). 

The “Show More Statistics” key can be selected to show second harmonic, third 
harmonic, and T.I.R. results for all spins. Column 5, rim average data, will not be 
shown in these cases. 

If the 

GSP9720JLR

 is equipped with StraightTrak

®

 LFM, there will be a page of 

lateral force statistics following the T.I.R. results. 

“Clear Data” can also be selected (key is only available in Service Mode) to erase the 
tabulated statistics data.   

If statistics are displayed in metric units, then the displayed ranges will be converted 
from inches to millimeters and from pounds to kilograms. 

GSP9720JLR Wheel Balancer Operation Instructions 

Road Force® Measurement Procedures 

x

 109 

Summary of Contents for GSP9700 Series






























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands