Hunter GSP9700 Series Page 121 Operation Instructions Manual Download | Manualshive

Page: 121 / 157

background image

Display Language

Selects the language for displays.

Print Language

Selects the language for printouts.

Printer

Sets up the correct printer. The current default printer is the Hewlett-Packard DeskJet
(with color reports).

Printout Paper Size Selection

Selects the correct size paper for printouts.

QuickMatch

QuickMatch can be disabled, enabled, or enabled with the toggle key.

Use Runout & Road Force Limits

This set up choice will allow the operator to enable or disable Runout & Road Force
limits.

Hood Autostart Feature

Enables or disables automatically starting the spin upon closing the hood.

Servo-Stop

Enables or disables the intelligent DC motor drive to automatically rotate the wheel to
the weight or ForceMatch Mark positions. Servo-Push may also be enabled, which
allows pushing the wheel (approximately 1/8 of a revolution) to cause the intelligent
DC motor drive to automatically rotate the wheel to the next weight or ForceMatch
Mark positions. Pressing the “START” key may still be used for this function.

Balance Checkspin

Enables or disables the load roller during balance verification spins. When enabled
the load roller will automatically disabled as necessary.

Weight Units

Use “Weight Units” to select English or Metric units for displaying wheel weights.

NOTE:

Balancer must be in service mode to view/change the
remaining set-up items: Set Date and Time, Prompt To Set
Date and Time, Balance Limits, Prompt for Wheel Assembly
ID and Spindle Type.

Refer to “5.4 Service Mode Setup and

Features” on page 114.

Inflation Station Units

Selects English or Metric units for air pressure, or disable the option altogether.

Runout Units

Selects English or Metric units for displaying runout measurements.

Road Force Units

Selects the desired units for road force measurement to be displayed on the screen
and in printouts. Select units in pounds, Newtons, or kilograms.

GSP9720JLR Wheel Balancer Operation Instructions

Equipment Information

x

113

«
...
119
120
121
122
123
...
»

Summary of Contents for GSP9700 Series






























































































































































Reviews:

No comments

Related manuals for GSP9700 Series

Brand: Daytona Pages: 19

Brand: Hofmann Megaplan Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands