Hunter GSP9700 Series Page 114 Operation Instructions Manual Download | Manualshive

Page: 114 / 157

background image

4.11 Harmonics & T.I.R. Data/Plots

A graphic depiction of the data displayed on the “Current Runout & Road Force”
popup screen can be viewed by selecting “Show Runout Plots” from the “Details”
popup screen.

The dotted line represents total indicated reading (T.I.R.), actual movement of the
load roller or Dataset® arms. The total indicated reading numeric data displayed is
the difference between the highest and lowest value measured. Harmonics are
calculated from the T.I.R. data and then shown graphed as a solid curve. The
harmonic numeric data displayed represents the difference between the highest and
lowest value of the curve.

Refer to “Harmonic Vibrations,” page 133.

During

Forcematching®, the first harmonic vibration of the tire is matched opposite of the
first harmonic vibration of the rim (average of the inner and outer measured flanges
or bead seats) to reduce the vibration of the wheel assembly.

Refer to

“Forcematching®,” page 82.

Viewing Multiple Harmonics

You may also select to see plots of multiple harmonic vibrations for the assembly, tire
or rim. Each time “Show Next Harmonic” is selected, the next harmonic amount will
be highlighted in color and the corresponding harmonic curve (such as a twice-per
revolution wave representing the second harmonic) will be plotted on the graph and
sized according to the highlighted amount.

Viewing Multiple Revolutions

The runout plots automatically show one complete revolution of the assembly by
default. The “Show All Revolutions” key may be selected to show all four measured
revolutions of data on the load roller plot or the two revolutions of data on the rim
plots. This makes it possible to view the data for consistency in measurement for
each revolution.

Assembly Data Plots Screen

When “Show Runout Plots” is selected, the “Rim and Load Roller Runout Plots”
screen will appear. The initial screen defaults to the first harmonic plot of the load
roller data for the assembly. The assembly lines are color coded to represent a
specific value as follows:

ASSEMBLY

1

ST

HARMONIC

(BROWN)

ASSEMBLY

T.I.R.

(WHITE)

106

x

Road Force® Measurement Procedures

GSP9720JLR Wheel Balancer Operation Instructions

«
...
112
113
114
115
116
...
»

Summary of Contents for GSP9700 Series






























































































































































Reviews:

No comments

Related manuals for GSP9700 Series

VIDEOTRONIC V653.G2

Brand: Fasep Pages: 24

Brand: HENNESSY INDUSTRIES Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands