Hunter GSP9700 Series Operation Instructions Manual Download

Page: 72 / 157

NOTE:

Note the location of the Dataset® arms on the rim. The
location for rim runout measurement is

NOT

the same as the

location for inputting rim dimensions for weight location.

When Dataset® arms are in place, press the outer arm button. The motor will slowly
rotate the wheel to measure runout. While the wheel is in motion,

gently apply

upward and inward fingertip pressure on both Dataset® arms as shown below:

CAUTION:

Take care when placing hands to measure rim runout that no
part of your hands or body interfere with parts in motion.

NOTE:

Do not grasp the Dataset® arms. Use fingertip pressure
only.

Balancing Procedures

GSP9720JLR Wheel Balancer Operation Instructions

Summary of Contents for GSP9700 Series






























































































































































Search results

Summary of Contents for GSP9700 Series

Reviews:

Related manuals for GSP9700 Series

Brands by name

Popular brands

Hunter GSP9700 Series, Operation Instructions Manual

Search results

Summary of Contents for GSP9700 Series

Reviews:

Related manuals for GSP9700 Series

Brands by name

Popular brands