Huawei TE80 Administrator'S Manual Download Page 57 | Manualshive

Page: 57 / 178

background image

HUAWEI TE80 Videoconferencing Endpoint
Administrator Guide

4 Display Device and Camera

Issue 02 (2014-03-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

49

Table 4-9

Capabilities of the TE80's video input ports

Port Name
on the UI

Port
Numbe
r on the
Rear
Panel

Type

Receivable
Input Format

Control Description

1 MAIN IN

1

DVI-I

VGA, YPbPr,
DVI, HDMI,
CVBS, and
S-VIDEO

Camera
PTZ

The DVI-I and
HD-VI ports are
mutually exclusive
and cannot be used
at the same time.

HD-VI

DVI(HW),
HDMI(HW),
and
YPbPr(HW)

Camera
PTZ

2 PC IN

2

DVI-I

VGA, YPbPr,
DVI, and
HDMI

Camera
PTZ

The DVI-I and
Display Port ports
are mutually
exclusive and
cannot be used at
the same time.

Display
Port

DP and HDMI

Camera
PTZ

3 AUX IN

3

HDMI

DVI and
HDMI

Camera
PTZ

The HDMI and
HD-VI ports are
mutually exclusive
and cannot be used
at the same time.

HD-VI

DVI(HW) and
HDMI(HW)

Camera
PTZ

4 3G-SDI IN

4

BNC

SDI

Camera
PTZ

None



PTZ is an acronym for Pan, Tilt, and Zoom. A PTZ camera supports panning, tilting, and zooming
control.



The HD-VI port can only be connected to the HUAWEI VPC600 or VPC620. After connecting this
port to the HUAWEI VPC600 or VPC620, you can perform PTZ controls on and supply power to
the HUAWEI VPC600 or VPC620 without additional cables.



If you connect a port other than the HD-VI port to the camera, you must connect the cable used for
transmitting VISCA control signals to the COM port on your endpoint to perform PTZ controls on
the camera.

Each input port to be used for transmitting a video or a presentation can be specified on the
user interface. For details, see section

6.1.1 Designating the Dual Streams

Select a video input port on your endpoint based on the video format supported by the camera.
Then connect the camera to your endpoint using the cable provided.

4.4 Configuring Video Input

Correct video input settings enable your endpoint to properly display video input from the
video input ports.

«
...
55
56
57
58
59
...
»

Summary of Contents for TE80



















































































































































































Reviews:

No comments

Related manuals for TE80

Brand: Samsung Pages: 2

Brand: Samsung Pages: 33

Brand: S.E.M. Pages: 6

Brand: Onn Pages: 11

Brand: KAR-TECH Pages: 55

Brand: Vansco Pages: 11

Brand: YA Pages: 2

Basic Digital Phone

Brand: Inter-Tel Pages: 90

Brand: Idemia Pages: 74

Brand: GRS Pages: 4

Brand: ATL Pages: 46

Brand: iWantit Pages: 32

Brand: Panasonic Pages: 22

Brand: Panasonic Pages: 27

Brand: Panasonic Pages: 33

Brand: Panasonic Pages: 15

Brand: Curtis Pages: 12

Brand: Philips Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands