Huawei TE80 Administrator'S Manual Download Page 131

Page: 131 / 178

HUAWEI TE80 Videoconferencing Endpoint
Administrator Guide

12 Troubleshooting

Issue 02 (2014-03-30)

Huawei Proprietary and Confidential

123

Figure 12-1

Diagnostics model

Figure 12-1

shows the diagnostics of three modules: audio module, video module, and

network transception module.

Audio signals are transmitted in the following signal path:



Local microphone → 1 → 5 → Communication network → 6 → 7 → Remote speaker



Local speaker ← 2 ← 5 ← Communication network ← 6 ← 8 ← Remote microphone

Video signals are transmitted in the following signal path:



Local camera → 3 → 5 → Communications network → 6 → 9 → Remote display
device



Local display device ← 4 ← 5 ← Communications network ← 6 ← 10 ← Remote
camera

Sound and Color Bar Tests

Table 12-1

describes sound and color bar tests.

Table 12-1

Sound and color bar tests

Test

Item to Be Tested

Signal Stream

Sound

2 audio output

2 → Speaker

Color bar

4 video output

4 → Display device



To perform a sound test, choose

Sound & Color Bar Test

Sound Test

. While the test

audio stored on your endpoint plays, check the sound quality.



To perform a color bar test, choose

Sound & Color Bar Test

Color Bar Test

. While

seven color bars are displayed on the display device, check the color display quality.

Loopback Tests

During a loopback test, your endpoint transmits audio or video data through a channel to
simulate actual working conditions and tests whether the output is satisfactory. You can

Summary of Contents for TE80



















































































































































































Search results

Summary of Contents for TE80

Reviews:

Related manuals for TE80

Brands by name

Popular brands

Huawei TE80, Administrator'S Manual

Search results

Summary of Contents for TE80

Reviews:

Related manuals for TE80

Brands by name

Popular brands