Huawei TE80 Administrator'S Manual Download Page 157

Page: 157 / 178

HUAWEI TE80 Videoconferencing Endpoint
Administrator Guide

13 Feature Configuration

Issue 02 (2014-03-30)

Huawei Proprietary and Confidential

149

Parameter

Description

Setting

remote sites.

Local listen
port

Specifies the local SIP listening port.

The default value is

5060

Value range: 1-65534.

Server listen
port

Specifies the listening port on the SIP
server with which your endpoint
registers.

The default value is

5060

Value range: 1-65534.

Port settings

Specifies the port use.



Normal

: The number of the port

currently in use cannot be changed.



Port convergence

: The port numbers

used in H.323 converge. Specifically,
signals of different formats use the
same port number. This saves port
resources.



Same port send/receive

: Your

endpoint sends and receives data
streams through the same port.

The default value is

Same port

send/receive

Audio port

Specifies the port your site uses to
receive audio packets during
communication with remote sites.

The default value is

10002

Enter an even number ranging
from 1 to 65534.

Video port

Specifies the port your site uses to
receive video packets during
communication with remote sites.

The default value is

10004

Enter an even number ranging
from 1 to 65534.

SIP TLS call
port

Specifies the port your site uses to send
SIP signaling during communication
with remote sites when

Transmission

type

is set to

TLS

The default value is

5061

Value range: 1-65534.

NOTE

For details about how to set

Transmission type

, see

3.1.4

Setting SIP Parameters

Local SIP
TLS listen
port

Specifies the local SIP listening port
when

Transmission type

is set to

TLS

SIP server
TLS listen
port

Specifies the listening port on the SIP
server with which your endpoint
registers when

Transmission type

is set

TLS

Use TCP to
transmit
streams

Specifies whether to use the
Transmission Control Protocol (TCP) to
transmit video and data streams.

NOTE

If you set this parameter to

Enable

, you must

also set

TCP listen port

and

TCP

connection port

The default value is

Disable

TCP listen
port

Specifies the local listening port for TCP
streams.

The default value is

20002

Value range: 1-65534.

Summary of Contents for TE80



















































































































































































Search results

Summary of Contents for TE80

Reviews:

Related manuals for TE80

Brands by name

Popular brands

Huawei TE80, Administrator'S Manual

Search results

Summary of Contents for TE80

Reviews:

Related manuals for TE80

Brands by name

Popular brands