Huawei TE80 Administrator'S Manual Download Page 23 | Manualshive

Page: 23 / 178

background image

HUAWEI TE80 Videoconferencing Endpoint
Administrator Guide

2 Basic Configuration and Verification

Issue 02 (2014-03-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

15

Verification Result

This example assumes that a video source is connected to the 1 MAIN IN port on the endpoint.
If the video delivered through the 1 MAIN IN port is correctly displayed on the display device
after you select

1 MAIN IN

, the video input and output of the endpoint are correct.

2.4 Power Management

The endpoint supports sleep mode. You can set its sleep time and automatic startup and
shutdown time.

To reduce power consumption, the endpoint can be configured to enter sleep mode after it has
been in the idle state for a defined period of time.

Procedure

Step 1

Choose

Advanced

>

Settings

>

General

>

Power supply

. Set the sleep and automatic startup

and shutdown parameters described in

Table 2-4

Sleep and automatic startup and shutdown parameters

Parameter

Description

Setting

Shut Down

Specifies whether the endpoint
can be powered off.

If you disable this parameter,
you can only restart the endpoint
or place it in sleep mode by

pressing

on the remote

control.

The default value is

Enable

.

Enter sleep mode

Specifies the period after which
the endpoint enters sleep mode if
you do not perform any
operations.

If you set this parameter to

Never

, the endpoint will never

automatically enter sleep mode.

The default value is

After 10

min

.

Wake-on-LAN

Specifies whether you can
remotely wake up a standby or
sleeping endpoint by sending
Wake on LAN (WOL) messages.

NOTE

A standby endpoint indicates that
the power switch on the endpoint's
rear panel is in the ON position and
that the endpoint is turned off by
pressing the power key on the
remote control.

This parameter is not selected by
default.

Scheduled
power-on

Specifies whether the endpoint
automatically powers on at the

This parameter is not selected by
default.

«
...
21
22
23
24
25
...
»

Summary of Contents for TE80



















































































































































































Reviews:

No comments

Related manuals for TE80

FINISH-OUT MC111M

Brand: M&S Systems Pages: 2

Brand: eMoMo Pages: 2

Brand: HEIDENHAIN Pages: 64

Brand: EMC-PARTNER Pages: 28

Brand: Favero Pages: 27

Brand: Tormatic Pages: 66

Brand: Daewoo Pages: 31

M3905 Call Center

Brand: Nortel Pages: 2

Brand: Laser Pages: 1

Brand: Panasonic Pages: 100

Brand: Raven Pages: 48

Brand: Boss Audio Systems Pages: 36

Brand: D-Link Pages: 13

Brand: D-Link Pages: 96

C7301U - Cd Rcvr W/ Custm Dsply

Brand: Panasonic Pages: 66

DCN-CONCM Concentus

Brand: Bosch Pages: 2

DCN Next Generation 4.41

Brand: Bosch Pages: 14

DCN-CON Concentus Delegate Unit

Brand: Bosch Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands