Huawei TaiShan 200 23280 User Manual Download Page 71

Page: 71 / 191

Item

Description

Ground cable

The 2280 does not provide a separate ground port. It is

grounded through the ground cable of a power cable. Ensure

that the power cables of the PSUs are in good contact.

5.9 Powering On the Server

Power on the server using one of the following methods based on the actual

situation:

●

If the PSUs are properly installed but are not connected to an external power

supply:
Connect the external power supply to the PSUs. Then the server will power on

with the PSUs.

NO TE

The default value of System State Upon Power Supply is Power on, which indicates

that the server automatically powers on after power is supplied to the PSUs. To

change the value of System State Upon Power Supply, log in to the iBMC WebUI and

choose Power > Power Control.

●

If the PSUs are properly installed and connected to the external power supply

and the server is in the standby state (the power indicator is steady yellow),

power on the server as follows:
–

Press the power button on the front panel to power on the server. For

details about the power button position, see

2.2 Front Panel Indicators

and Buttons

–

Power on the server using the iBMC WebUI.
i.

5.11.4 Logging In to the

iBMC WebUI

5.12.4 Logging In to the iBMC WebUI

ii. Open the Power Control page.

○

For iBMC V549 or earlier, choose Power > Power Control.

○

For iBMC V561 and V3.01.00.00 or later, choose System > Power

> Power Control.

iii. Click Power On. In the displayed dialog box, click Yes to power on

the server.

–

Power on the server using the Remote Virtual Console.
i.

8.2.1 Logging

In to the Remote Virtual Console through the iBMC WebUI

9.2.1 Logging In to the Remote Virtual Console through the iBMC

WebUI

ii. On the KVM screen, click or

on the menu bar.

iii. Choose Power On.

A dialog box is displayed.

iv. Click Yes to power on the server.

TaiShan 200 Server (Model 2280)

User Guide

5 Installation and Configuration

Issue 09 (2021-01-12)

Summary of Contents for TaiShan 200 23280
































































































































































































Search results

Summary of Contents for TaiShan 200 23280

Reviews:

Related manuals for TaiShan 200 23280

Brands by name

Popular brands

Huawei TaiShan 200 23280, User Manual

Search results

Summary of Contents for TaiShan 200 23280

Reviews:

Related manuals for TaiShan 200 23280

Brands by name

Popular brands