Huawei TaiShan 200 23280 User Manual Download Page 189

Page: 189 / 191

Sensor

Description

Component

CPU

Memory

DIMM status

DIMMs of CPU

indicates

the DIMM number. The value

is 1 or 2.

Fan Status

PSU fan status

PSU.

indicates the PSU

number. The value is 1 or 2.

Temp Status

PSU presence

Status

PSU status

Power Button

Power button status

Right mounting ear

UID Button

UID button status

DISK

Drive status

Drive.

indicates the

physical drive slot number.

FAN

Presence

Fan presence

Fan module.

indicates the

fan module number. The

value ranges from 1 to 4.

FAN

Status

Fan status

RTC Battery

RTC battery status. An

alarm is generated when

the voltage is lower than

1 V.

CMOS battery

DIMM

DIMM status

DIMM.

indicates the DIMM

slot number.

Inlet Temp

PSU air inlet temperature PSU.

indicates the PSU

number. The value is 1 or 2.

PS Redundancy

Redundancy failure due

to PSU removal

PSU

BMC Boot Up

BMC startup events

N/A.

indicates the

component ID.

SEL Status

SEL full or clearing

events

Op. Log Full

Operation log full or

clearing events

Sec. Log Full

Security log full or

clearing events

CPU Usage

CPU usage

Memory Usage

Memory usage

BMC Time Hopping

Time hopping

NTP Sync Failed

NTP synchronization

failure and recovery

events

TaiShan 200 Server (Model 2280)

User Guide

A Appendix

Issue 09 (2021-01-12)

181

Summary of Contents for TaiShan 200 23280
































































































































































































Search results

Summary of Contents for TaiShan 200 23280

Reviews:

Related manuals for TaiShan 200 23280

Brands by name

Popular brands

Huawei TaiShan 200 23280, User Manual

Search results

Summary of Contents for TaiShan 200 23280

Reviews:

Related manuals for TaiShan 200 23280

Brands by name

Popular brands