Huawei SUN2000-60KTL-M0 User Manual Download Page 65

Page: 65 / 127

Figure 5-31 Bundling communications cables

Step 5 Tighten the thread-lock sealing nut and seal the cable gland.

----End

5.6.3 (Optional) Installing the Solar Tracker Power Cable

Precautions

NO TICE

● A switch-disconnector-fuse or fuse-switch-disconnector with a voltage of no

less than 500 V, current of 16 A, and protection type of gM needs to be

installed between the SUN2000 and the tracker controller for protection.

● The cable between the wiring terminal on the power cable and the switch-

disconnector-fuse or fuse-switch-disconnector should be less than or equal to

2.5 meters.

Cable Specifications

Recommended: dual-layer three-core outdoor copper cable with a conductor

cross-sectional area of 10 mm

WARNING

Do not place flammable materials around the cable.

Procedure

Step 1 Remove an appropriate length of the jacket and insulation layer from the tracking

power cable using a wire stripper. (Ensure that the jacket is in the maintenance

compartment.)

SUN2000-(60KTL, 65KTL)-M0

User Manual (Mexico Edition)

5 Electrical Connections

Issue 06 (2020-10-12)

Summary of Contents for SUN2000-60KTL-M0
































































































































Search results

Summary of Contents for SUN2000-60KTL-M0

Reviews:

Related manuals for SUN2000-60KTL-M0

Brands by name

Popular brands

Huawei SUN2000-60KTL-M0, User Manual

Search results

Summary of Contents for SUN2000-60KTL-M0

Reviews:

Related manuals for SUN2000-60KTL-M0

Brands by name

Popular brands