Huawei SUN2000-60KTL-M0 User Manual Download Page 100

Page: 100 / 127

No.

Parameter

Description

Unit

Remarks

Overfrequency

derating

If this parameter is enabled,

the active power of the

inverter will be derated

according to a certain slope

when the grid frequency

exceeds the value that

triggers overfrequency

derating.

N/A

Trigger

frequency of

over frequency

derating

The standards of certain

countries and regions require

that the output active power

of the SUN2000 be derated

when the grid frequency

exceeds a certain value.

N/A

Quit frequency

of over

frequency

derating

Specifies the frequency

threshold for exiting

overfrequency derating.

N/A

Cutoff

frequency of

overfrequency

derating

Specifies the frequency

threshold for cutting off

overfrequency derating.

N/A

Cutoff power of

overfrequency

derating

Specifies the power threshold

for cutting off overfrequency

derating.

N/A

Power recovery

gradient of

overfrequency

derating

Specifies the power recovery

gradient for overfrequency

derating.

%/min

N/A

SUN2000-(60KTL, 65KTL)-M0

User Manual (Mexico Edition)

7 Man-Machine Interactions

Issue 06 (2020-10-12)

Summary of Contents for SUN2000-60KTL-M0
































































































































Search results

Summary of Contents for SUN2000-60KTL-M0

Reviews:

Related manuals for SUN2000-60KTL-M0

Brands by name

Popular brands

Huawei SUN2000-60KTL-M0, User Manual

Search results

Summary of Contents for SUN2000-60KTL-M0

Reviews:

Related manuals for SUN2000-60KTL-M0

Brands by name

Popular brands