Huawei SUN2000-60KTL-M0 User Manual Download Page 32

Page: 32 / 127

Figure 4-5 Stacked installation mode (not recommended)

4.4 Installing the Mounting Bracket

Installation Precautions

Figure 4-6

shows the SUN2000 mounting bracket dimensions.

Figure 4-6 Mounting bracket dimensions

NO TE

The SUN2000 mounting bracket has four groups of tapped holes, each group containing

four tapped holes. Mark any hole in each group based on site requirements and mark four

holes in total. Two round holes are preferred.

Before installing the mounting bracket, remove the security torx wrench from the

mounting bracket and save it for later use.

SUN2000-(60KTL, 65KTL)-M0

User Manual (Mexico Edition)

4 Installation

Issue 06 (2020-10-12)

Summary of Contents for SUN2000-60KTL-M0
































































































































Search results

Summary of Contents for SUN2000-60KTL-M0

Reviews:

Related manuals for SUN2000-60KTL-M0

Brands by name

Popular brands

Huawei SUN2000-60KTL-M0, User Manual

Search results

Summary of Contents for SUN2000-60KTL-M0

Reviews:

Related manuals for SUN2000-60KTL-M0

Brands by name

Popular brands