background image

About This Document

Purpose

This document describes the SUN2000-60KTL/65KTL-M0 (SUN2000 for short) in

terms of its installation, electrical connections, commissioning, maintenance, and

troubleshooting. Before installing and operating the SUN2000, ensure that you are

familiar with the features, functions, and safety precautions provided in this

document.

Intended Audience

This document is intended for photovoltaic (PV) plant personnel and electrical

technicians.

Symbol Conventions

The symbols that may be found in this document are defined as follows.

Symbol

Remarks

Indicates a hazard with a high level of risk

which, if not avoided, will result in death or

serious injury.

Indicates a hazard with a medium level of risk

which, if not avoided, could result in death or

serious injury.

Indicates a hazard with a low level of risk

which, if not avoided, could result in minor or

moderate injury.

SUN2000-(60KTL, 65KTL)-M0

User Manual (Mexico Edition)

About This Document

Issue 06 (2020-10-12)

Copyright © Huawei Technologies Co., Ltd.

ii

Summary of Contents for SUN2000-60KTL-M0
































































































































Reviews: