Huawei SUN2000-60KTL-M0 User Manual Download Page 53

Page: 53 / 127

Figure 5-13 DC terminals

Select DC input terminals according to the following rules:
1. Evenly distribute DC input power cables on the DC input terminals controlled

by the two DC switches.

2. Maximize the number of connected MPPT circuits.

Cable Specifications

Cable Type

Conductor Cross-Sectional Area

(mm

)

Cable Outer

Diameter (mm)

Range

Recommended

value

PV cable that meets

the 1100 V standard

4.0–6.0 (12–10

AWG)

4.0 (12 AWG)

4.5–7.8

NO TICE

Cables with high rigidity, such as armored cables, are not recommended, because

poor contact may be caused by the bending of the cables.

Procedure

Step 1 Prepare positive and negative connectors.

CA UTION

Use the Amphenol Helios H4 PV connectors provided with the SUN2000. If the

terminals are lost or damaged, purchase the PV connectors of the same model.

The device damaged caused by incompatible PV connectors is not covered under

any warranty or service agreement.

SUN2000-(60KTL, 65KTL)-M0

User Manual (Mexico Edition)

5 Electrical Connections

Issue 06 (2020-10-12)

Summary of Contents for SUN2000-60KTL-M0
































































































































Search results

Summary of Contents for SUN2000-60KTL-M0

Reviews:

Related manuals for SUN2000-60KTL-M0

Brands by name

Popular brands

Huawei SUN2000-60KTL-M0, User Manual

Search results

Summary of Contents for SUN2000-60KTL-M0

Reviews:

Related manuals for SUN2000-60KTL-M0

Brands by name

Popular brands