Huawei SUN2000-60KTL-M0 User Manual Download Page 91

Page: 91 / 127

Figure 7-5 Grid parameters (special user)

----End

Parameter List

NO TE

Vn represents the rated voltage and Fn represents the rated frequency.

No.

Parameter

Description

Unit

Grid code

Set this parameter based on the grid code of

the country or region where the SUN2000 is

used and the SUN2000 application scenario.

N/A

Isolation

Specifies the working mode of the SUN2000

according to the grounding status at the DC

side and the connection status to the grid.

N/A

Auto start upon grid

recovery

Specifies whether to allow the SUN2000 to

automatically start after the power grid

recovers.

N/A

Grid connection

duration after power

grid recovery

Specifies the waiting time for SUN2000 restart

after the power grid recovers.

Grid reconnection

voltage upper limit

The standards of certain countries and regions

require that the SUN2000 must not export

power to the power grid again when the grid

voltage exceeds the value of Grid reconnection

voltage upper limit after the SUN2000 shuts

down due to a fault.

SUN2000-(60KTL, 65KTL)-M0

User Manual (Mexico Edition)

7 Man-Machine Interactions

Issue 06 (2020-10-12)

Summary of Contents for SUN2000-60KTL-M0
































































































































Search results

Summary of Contents for SUN2000-60KTL-M0

Reviews:

Related manuals for SUN2000-60KTL-M0

Brands by name

Popular brands

Huawei SUN2000-60KTL-M0, User Manual

Search results

Summary of Contents for SUN2000-60KTL-M0

Reviews:

Related manuals for SUN2000-60KTL-M0

Brands by name

Popular brands