Huawei SUN2000-60KTL-M0 User Manual Download Page 36

Page: 36 / 127

NO TE

You need to prepare expansion bolts. M12x60 stainless steel expansion bolts are

recommended.

Figure 4-12 Drilling a hole and installing an expansion bolt

WARNING

Avoid drilling holes in the utility pipes and/or cables attached to back of the wall.

NO TICE

● To prevent dust inhalation or contact with eyes, wear safety goggles and an

anti-dust respirator when drilling holes.

● Clean up any dust in and around the holes using a vacuum cleaner and

measure the distance between holes. If the holes are inaccurately positioned,

drill a new set of holes.

● Level the head of the expansion sleeve with the concrete wall after removing

the bolt, spring washer, and flat washer. Otherwise, the mounting bracket will

not be securely installed on the concrete wall.

Step 3 Align the mounting bracket holes with the drilled holes, insert expansion bolts into

the holes through the mounting bracket, and then tighten the expansion bolts.

SUN2000-(60KTL, 65KTL)-M0

User Manual (Mexico Edition)

4 Installation

Issue 06 (2020-10-12)

Summary of Contents for SUN2000-60KTL-M0
































































































































Search results

Summary of Contents for SUN2000-60KTL-M0

Reviews:

Related manuals for SUN2000-60KTL-M0

Brands by name

Popular brands

Huawei SUN2000-60KTL-M0, User Manual

Search results

Summary of Contents for SUN2000-60KTL-M0

Reviews:

Related manuals for SUN2000-60KTL-M0

Brands by name

Popular brands