Huawei OceanStor 18500 V3 Features Manual Download Page 40 | Manualshive

Page: 40 / 183

background image

replication cannot implement data backup and disaster recovery in the scenario where a host
writes data to multiple dependent primary LUNs. A consistency group ensures data
consistency of secondary LUNs of all remote replication pairs in the group at the same point
in time (for example, the data of all secondary LUNs are the data copy of its primary LUN at
3:00 PM today), therefore ensures the data availability of primary LUNs after disaster
recovery.

3.8 Verifying the Configuration

After remote replication/consistency group is configured, you can view the status of the data
on the primary and secondary storage systems to check whether data replication between the
primary and secondary LUNs is successful.

3.1 Configuration Process

This section describes how to configure remote replication. You can set up a pair relationship
between the primary resource and secondary resource to implement data synchronization.

shows the process of configuring remote replication.

Figure 3-1

Process for configuring remote replication

Start

Check the remote

replication license

Add a remote device

Create a remote

replication

Mandatory

Optional

Note:

Add a route

When the local and remote storage
systems connect through iSCSI host
ports, and they locate on different
network segments, add a route.

End

Prepare configuration

Obtain remote replication license and
identify port type for connecting primary
storage device and secondary storage
device.

Verify the Configuration

OceanStor V3 Series
Remote Replication Feature Guide for Block

3 Configuring Remote Replication

Issue 06 (2018-01-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

32

«
...
38
39
40
41
42
...
»

Summary of Contents for OceanStor 18500 V3
























































































































































































Reviews:

No comments

Related manuals for OceanStor 18500 V3

Brand: Secure Data Pages: 2

Duramax Yardmate

Brand: USP Pages: 25

Paletto 00108043

Brand: Hama Pages: 4

Brand: Frontier Pages: 6

SmartStore SM2520

Brand: Riverlea Pages: 16

Brand: OYEN DIGITAL Pages: 1

Brand: Dancover Pages: 30

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brand: Sony Pages: 24

Brand: Sony Pages: 28

Brand: Sony Pages: 2

Brand: Sony Pages: 1

Brand: Sony Pages: 2

SDX-470V Series

Brand: Sony Pages: 32

Brand: Sony Pages: 28

SDX-260V Series

Brand: Sony Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands