Huawei OceanStor 18500 V3 Features Manual Download Page 132

Page: 132 / 183

Parameter

Description

Health Status

Indicates whether the consistency group is
functioning normally. The values include:

Normal

: The consistency group is

functioning normally. You can perform
the synchronization operation.

Fault

: The consistency group

malfunctions or the replication link is
down, you cannot perform the
synchronization operation.

Running Status

Indicates the consistency group is running
properly. The values include:

Normal

: Consistency group has

completed synchronization successfully.

Synchronizing

: Pair is synchronizing

data.

Split

: Consistency group is in the split

status, and the synchronization is
suspended.

Interrupted

: The remote replication

internal I/O error or the replication link
is down, and you cannot perform the
synchronization operation temporarily.

To be recovered

: After the remote

replication internal I/O error is rectified
or the replication link is up, and if

Recovery Policy

Manual

, the

consistency group enters this status. You
need to manually start synchronization
for the consistency group to synchronize
data.

Invalid

: Consistency group is useless

and cannot be restored in this status,
except deleting it. You must delete the
consistency group on both primary and
secondary storage devices. Otherwise,
the consistency group creation may fail.

OceanStor V3 Series
Remote Replication Feature Guide for Block

7 Managing Consistency Groups

Issue 06 (2018-01-30)

Huawei Proprietary and Confidential

124

Summary of Contents for OceanStor 18500 V3
























































































































































































Search results

Summary of Contents for OceanStor 18500 V3

Reviews:

Related manuals for OceanStor 18500 V3

Brands by name

Popular brands

Huawei OceanStor 18500 V3, Features Manual

Search results

Summary of Contents for OceanStor 18500 V3

Reviews:

Related manuals for OceanStor 18500 V3

Brands by name

Popular brands