Huawei OceanStor 18500 V3 Features Manual Download

Page: 146 / 183

Precautions

Based on

Running Status

of a consistency group, determine whether remote

replications in the consistency group can be split, as shown in

Table 7-5

Status requirements for splitting remote replications in a consistency group

Running Status of a Consistency
Group

Splitting Remote Replications in a
Consistency Group

Normal

√

Split

Interrupted (Link down)

√

(Can be performed only on the primary

device of a consistency group.)

Interrupted (Link up)

√

To be recovered

√

Invalid

Synchronizing

√

: Able to operate.

×: Unable to operate.

When synchronous consistency groups are splitting, if the storage system has a controller
reset, which may cause synchronization failure in some remote replication tasks, the
consistency groups cannot guarantee data consistency.

Procedure

Step 1

Step 2

Choose

Data Protection

Remote Replication

Consistency Group

Step 3

Right-click the desired consistency group and choose

Split

The security alert dialog box is displayed.

Step 4

Confirm the operation of splitting remote replications in the consistency group.

Carefully read the contents of the dialog box. Select

I have read and understand the

consequences associated with performing this operation.

and click

to confirm the

information.

Click

The

Success

dialog box is displayed indicating that the operation is successful.

Click

----End

OceanStor V3 Series
Remote Replication Feature Guide for Block

7 Managing Consistency Groups

Issue 06 (2018-01-30)

Huawei Proprietary and Confidential

138

Summary of Contents for OceanStor 18500 V3
























































































































































































Search results

Summary of Contents for OceanStor 18500 V3

Reviews:

Related manuals for OceanStor 18500 V3

Brands by name

Popular brands

Huawei OceanStor 18500 V3, Features Manual

Search results

Summary of Contents for OceanStor 18500 V3

Reviews:

Related manuals for OceanStor 18500 V3

Brands by name

Popular brands