Huawei IPC6521-Z20-FI User Manual Download Page 66

Page: 66 / 134

IPC6521-Z20-FI 1080P Intelligent Network Speed
Dome
User Guide

5 Device Configuration

Issue 02 (2013-09-30)

Huawei Proprietary and Confidential



If the object is not marked on the live video image, removed object detection is not
properly configured or not enabled.

Table 5-16

lists the possible causes and their

solutions.

Table 5-16

Possible causes

Cause

Solution

The surveillance area is too large.

Adjust the focal length and dimensions of
the surveillance area to ensure that the
intended object can be detected.

The surveillance area is too small.

The behavior analysis function is disabled.

Enable the behavior analysis function.

The sensitive area is not in

Enable

state

when

Behavior type

is set to

Removed

object detection

on the

Behavior Analysis

Parameters

page.

Select the sensitive area ID from the
sensitive area list and click

Enable/Disabled

to enable the sensitive

area.

Video alarm deployment

is not selected on

the

Alarm Deployment Policy

page that is

displayed when you choose

Settings

Alarm Configuration

Alarm

Deployment Policy

Select

Video alarm deployment

5.3.7 Configuring the Tripwire Detection Function

The tripwire detection function checks whether a person or an object crosses a specified
tripwire in a specified direction. The system generates an alarm when a person or an object
crosses the tripwire.

Prerequisite

Enable the behavior analysis function. For details, see

5.3.1 Enabling Behavior Analysis

Switch

After clicking a domain or a link to jump to a required page, you can press

Alt+←

(left arrow key) to

return to the previous page.

Procedure

Step 1

Step 2

Choose

Settings

Intelligent Analysis

Behavior Analysis Parameters

The

Behavior Analysis Parameters

page is displayed.

Step 3

Set

Behavior type

Tripwire detection

, as shown in

Figure 5-15

Summary of Contents for IPC6521-Z20-FI







































































































































Search results

Summary of Contents for IPC6521-Z20-FI

Reviews:

Related manuals for IPC6521-Z20-FI

Brands by name

Popular brands

Huawei IPC6521-Z20-FI, User Manual

Search results

Summary of Contents for IPC6521-Z20-FI

Reviews:

Related manuals for IPC6521-Z20-FI

Brands by name

Popular brands