Huawei E8000E-X16 Manual Download Page 8

Page: 8 / 182

3.6.2 DC Power Supply System.......................................................................................................................45
3.6.3 AC Power Supply System.......................................................................................................................46

3.7 Heat Dissipation System...................................................................................................................................49

3.8 Switching Network...........................................................................................................................................54

3.8.1 Introduction to the Switching Network System......................................................................................54
3.8.2 SFUI-40-C...............................................................................................................................................55

3.9 Control Plane....................................................................................................................................................57

3.9.1 Introduction to the Control Plane............................................................................................................57
3.9.2 SRUA.......................................................................................................................................................58
3.9.3 CMU........................................................................................................................................................63

4 E8000E-X3 Chassis Overview....................................................................................................67

4.6.1 Features and Diagram of the Power Supply System...............................................................................74
4.6.2 DC Power Supply Module.......................................................................................................................74
4.6.3 AC Power Supply Module.......................................................................................................................76

4.7 Heat Dissipation System...................................................................................................................................78

4.7.1 System Air Channel.................................................................................................................................78
4.7.2 Fan Module..............................................................................................................................................79
4.7.3 Air Filter..................................................................................................................................................81

4.8 Control Plane....................................................................................................................................................82

4.8.1 Introduction to the Control Plane............................................................................................................82
4.8.2 MPUD......................................................................................................................................................83

5 Boards............................................................................................................................................87

5.1 SPUA................................................................................................................................................................88
5.2 LPUF-40-A and FPIC.......................................................................................................................................90

5.3 LPUF-21 and FPIC.........................................................................................................................................101

5.3.1 LPUF-21................................................................................................................................................101
5.3.2 1-port 10GBase LAN/WAN-XFP FPIC................................................................................................103
5.3.3 12-port 100Base-FX/1000Base-X-SFP FPIC........................................................................................106

HUAWEI Eudemon8000E Firewall
Hardware Description

Contents

Issue 01 (2012-11-07)

Huawei Proprietary and Confidential

vii

Summary of Contents for E8000E-X16























































































































































































Search results

Summary of Contents for E8000E-X16

Reviews:

Related manuals for E8000E-X16

Brands by name

Popular brands

Huawei E8000E-X16, Manual

Search results

Summary of Contents for E8000E-X16

Reviews:

Related manuals for E8000E-X16

Brands by name

Popular brands