Huawei E8000E-X16 Manual Download Page 45

Page: 45 / 182

E8000E-X8 Chassis Overview

About This Chapter

This chapter describes the components, system configuration, physical specification, power
supply and heat dissipation system of the E8000E-X8.

3.1 System Overview

This section describes the system architecture and features.

3.2 Components of the E8000E-X8

This section describes the components of the E8000E-X8.

3.3 Slots Layout and Supported Boards

This section describes slots layout and supported boards of the E8000E-X8.

3.4 System Configuration

This section describes the system configuration of the E8000E-X8.

3.5 Physical Specification

This section describes the physical parameters of the E8000E-X8.

3.6 Power Supply System

This chapter describes the power supply system of the E8000E-X8.

3.7 Heat Dissipation System

This section describes the appearance, functions, and specifications of the heat dissipation
system.

3.8 Switching Network

This chapter describes the features and functions of a switching network.

3.9 Control Plane

This chapter describes the control plane of the E8000E-X8.

HUAWEI Eudemon8000E Firewall
Hardware Description

3 E8000E-X8 Chassis Overview

Issue 01 (2012-11-07)

Huawei Proprietary and Confidential

Summary of Contents for E8000E-X16























































































































































































Search results

Summary of Contents for E8000E-X16

Reviews:

Related manuals for E8000E-X16

Brands by name

Popular brands

Huawei E8000E-X16, Manual

Search results

Summary of Contents for E8000E-X16

Reviews:

Related manuals for E8000E-X16

Brands by name

Popular brands