Huawei E8000E-X16 Manual Download | Manualshive

Page: 38 / 182

background image

Table 2-15

Buttons and indicators on the panel of the MPUB

Indicator/Button

Description

OFL button

To remove a board, you must press and hold the button for six
seconds until the OFL indicator turns on.
This button takes effect only on the slave MPUB.

OFL indicator (red)

If the indicator is on, you can remove the board.

RUN indicator (green)

If the indicator blinks once every two seconds (0.5 Hz), the
system is in the normal state.
If the indicator blinks twice each second (2 Hz), the system is in
the alarm state.

ALM indicator (red)

If the indicator is steady on, the system is in the alarm state.
If the indicator is steady off, the system is in the normal state.

ACT active/standby
indicator (green)

If the indicator is steady on, the MPUB is in the active state.
If the indicator is off, the MPUB is in the standby state.

Reset button

The button is used for resetting the MPUB. If you press the Reset
button, you can reset the MPUB.

CF ACT indicator (green) If the indicator is on, the CF is in position.

If the indicator is blinking, data is being read or written.
If the indicator is off, the CF is not in position or can be removed.

CF OFL button

If you press the CF OFL button, all operations on the CF card
will be ended and the CF card will be powered off.

SFP LINK/ACT indicator
(green)

If the indicator is steady on, the link is normal.
If the indicator is blinking, data is being transmitted.

MGMT-ETH LINK
indicator (green) (on
Ethernet network
interfaces)

If the indicator is steady on, the link is normal.
If the indicator is off, the link is Down.

MGMT-ETH ACT
indicator (amber) (on
Ethernet interfaces)

If the indicator is blinking, data is being transmitted.
If the indicator is off, no data is being transmitted.

describes the interfaces on the MPUB and their uses.

Table 2-16

Interfaces on the MPUB and their uses

Interface Name

Connector Type Description

USB interface

USB

Not supported.

HUAWEI Eudemon8000E Firewall
Hardware Description

2 E8000E-X16 Chassis Overview

Issue 01 (2012-11-07)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

28

«
...
36
37
38
39
40
...
»

Summary of Contents for E8000E-X16























































































































































































Reviews:

No comments

Related manuals for E8000E-X16

Brand: D-Link Pages: 6

Brand: Clavister Pages: 76

Brand: Fortinet Pages: 2

SecPath F50X0-D Series

Brand: H3C Pages: 39

Unified Security Gateway ZyWALL 300

Brand: ZyXEL Communications Pages: 4

Brand: Nexcom Pages: 76

Brand: Lanner Pages: 64

NextGen X Series

Brand: Barracuda Networks Pages: 4

Brand: ZyXEL Communications Pages: 2

Unified Security Gateway ZyWALL 300

Brand: ZyXEL Communications Pages: 6

Brand: H3C Pages: 6

Brand: Check Point Pages: 4

NetGuardian 216T

Brand: DPS Telecom Pages: 4

Brand: DPtech Pages: 277

Brand: AXIOMTEK Pages: 52

Brand: AXIOMTEK Pages: 60

Brand: AXIOMTEK Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands