Huawei E8000E-X16 Manual Download

Page: 71 / 182

Table 3-16

Interfaces on the SRUA and their uses

Interface Name

Connector
Type

Description

USB interface

USB

Not supported.

CF card interface

TYPE II
(compatible
with TYPE I)

It is used to hold a CF card to store data files as
a massive storage device.

CTL-ETH-SFP interface
(1000MBase-X)

SFP

It is reserved for the use after capacity
expansion.

MGMT-ETH interface
(10M/100M/1000M
Base-TX auto-sensing)

RJ45

It connects to the NMS workstation and has
LINK and ACT indicators.

Console interface

RJ45

It connects to the console for on-site
configuration of the system.

AUX interface

RJ45

It connects to the Modem for remote
maintenance through dialing.

Interface Attributes

Table 3-17

lists the 1000MBase-X-SFP interface attributes.

Table 3-17

1000MBase-X-SFP interface attributes

Attribute

Description

Connector type

SFP

Operation mode

1000 M fiber

Standard
compliance

IEEE 802.3-2002

Cable
specification

Single-mode or multi-mode fibers

Table 3-18

lists the 10Base-T/100Base-TX/1000Base-T-RJ45 interface attributes.

Table 3-18

10Base-T/100Base-TX/1000Base-T-RJ45 interface attributes

Attribute

Description

Connector type

RJ45

Operation mode

10M/100M/1000M auto-sensing interfaces, supporting full-duplex mode

HUAWEI Eudemon8000E Firewall
Hardware Description

3 E8000E-X8 Chassis Overview

Issue 01 (2012-11-07)

Huawei Proprietary and Confidential

Summary of Contents for E8000E-X16























































































































































































Search results

Summary of Contents for E8000E-X16

Reviews:

Related manuals for E8000E-X16

Brands by name

Popular brands

Huawei E8000E-X16, Manual

Search results

Summary of Contents for E8000E-X16

Reviews:

Related manuals for E8000E-X16

Brands by name

Popular brands