Huawei E8000E-X16 Manual Download Page 67 | Manualshive

Page: 67 / 182

background image

Table 3-14

Technical specifications of the SFUI-40-C

Item

Description

Silkscreen of the board name

SFUI-40-C

Dimensions (W x D x H)

400 mm x 553.5 mm x 35 mm

Power consumption (typical value)

40 W

Board weight

3.5 kg

3.9 Control Plane

This chapter describes the control plane of the E8000E-X8.

3.9.1 Introduction to the Control Plane

This section describes the functions of the control plane.

E8000E-X8 uses the SRUA and CMU to implement the functions of the control plane. The
functions are described as follows:

System Control and Management Unit

As the system control and management unit, the SRUA provides the following functions on the
system control panel:

l

Route calculation: All routing protocol packets are sent by the forwarding engine to the
SRUA for processing. In addition, the SRUA broadcasts and filters packets, and downloads
routing policies from the policy server.

l

Outband communication between boards: The LAN switch modules integrated on the
SRUA provide outband communications between boards. In this manner, messages can be
controlled, maintained, and exchanged between the boards.

l

Device management and maintenance: Devices can be managed and maintained through
the management interfaces (serial interfaces) provided by the SRUA.

l

Data configuration: The SRUA stores configuration data, startup files, charging
information, upgrade software, and system logs.

l

Data storage: The SRUA provides two interfaces for CF cards, which serve as mass storage
devices to store data files.

System Maintenance Unit

As the system maintenance unit, the SRUA collects system monitoring information to test system
units locally or remotely, or implement in-service upgrading of system units.

The SRUA periodically collects information about the operation of system units through the
Monitorbus. The SRUA then generates related control information based on the collected
information, for example, the detection of board installations and adjustments to fan speed.
Through the joint test action group (JTAG) bus, the SRUA remotely or locally tests system units,
or performs in-service upgrading of system units.

HUAWEI Eudemon8000E Firewall
Hardware Description

3 E8000E-X8 Chassis Overview

Issue 01 (2012-11-07)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

57

«
...
65
66
67
68
69
...
»

Summary of Contents for E8000E-X16























































































































































































Reviews:

No comments

Related manuals for E8000E-X16

Brand: Meraki Pages: 9

Brand: NETGEAR Pages: 2

Brand: Fortinet Pages: 62

Brand: Fortinet Pages: 12

FortiGate 1000D

Brand: Fortinet Pages: 14

Brand: Fortinet Pages: 20

Brand: Fortinet Pages: 54

Brand: Fortinet Pages: 56

SecPath F5000 Series

Brand: H3C Pages: 51

NetDefend DFL-860E

Brand: D-Link Pages: 6

ZyXEL ZyWALL USG-1000

Brand: ZyXEL Communications Pages: 986

Brand: Thales Pages: 37

TippingPoint TPS 8200TX

Brand: Trend Micro Pages: 9

FortiManager-3000B

Brand: Fortinet Pages: 2

FortiManager-3000

Brand: Fortinet Pages: 2

FortiMail-4000A

Brand: Fortinet Pages: 2

Brand: Fortinet Pages: 2

FortiMail-3000C

Brand: Fortinet Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands