Huawei E8000E-X16 Manual Download

Page: 101 / 182

CAUTION

The LPUF-40-A backplane does not support the hot swap of FPICs.

Figure 5-4

shows the appearance of the LPUF-40-A.

Figure 5-4

Appearance of the LPUF-40-A

Panel

Figure 5-5

describes the panel appearance of the LPUF-40-A.

Table 5-4

lists the indicators on

the panel.

Figure 5-5

Panel appearance of the LPUF-40-A

RUN

Table 5-4

Indicators and button on the panel of the LPUF-40-A

Indicator/Button

Description

OFL button

It is a button to send a application signal to the device when removing
a board. Before removing a board, you need to press and hold the

OFL

button for about 6s till the

OFL

indicator is on.

OFL indicator (red)

If the indicator is on, you can remove the board.

RUN indicator
(green)

If the indicator blinks once every 2s (0.5 Hz), the LPU is in the normal
state.

HUAWEI Eudemon8000E Firewall
Hardware Description

5 Boards

Issue 01 (2012-11-07)

Huawei Proprietary and Confidential

Summary of Contents for E8000E-X16























































































































































































Search results

Summary of Contents for E8000E-X16

Reviews:

Related manuals for E8000E-X16

Brands by name

Popular brands

Huawei E8000E-X16, Manual

Search results

Summary of Contents for E8000E-X16

Reviews:

Related manuals for E8000E-X16

Brands by name

Popular brands