Huawei E8000E-X16 Manual Download

Page: 108 / 182

Table 5-16

Transmission distance of 10G XFP optical modules

Core(µm)

Modal/Bandwidth
(Mhz*km)

Transmission Distance
(m)

2000

2-300

500

2-82

62.5

200

2-33

Technical Specifications

Table 5-17

lists the technical specifications of the 2-port 10GBase LAN/WAN-XFP FPIC.

Table 5-17

Technical specifications of the 2-port 10GBase LAN/WAN-XFP FPIC

Item

Specifications

Silkscreen of the board name P40-2x10GBase LAN/WAN-XFP

Power consumption (typical
value)

12 W

Heat dissipation

39 BTU/hour

Board weight

0.5 kg

Dimensions (width x depth x
height)

180 mm x 145 mm x 40 mm

5.2.4 4-port 10GBase LAN/WAN-XFP FPIC

Overview

The 4-port 10GBase WAN/LAN-XFP FPIC supports two working modes: LAN and WAN.

NOTE

The 4-port 10GBase WAN/LAN-XFP FPIC is convergence .

Panel

Figure 5-8

shows the panel appearance of the 4-port 10GBase WAN/LAN-XFP FPIC.

Table

5-18

describes the indicators on the panel.

Figure 5-8

Panel appearance of the the 4-port 10GBase WAN/LAN-XFP FPIC

HUAWEI Eudemon8000E Firewall
Hardware Description

5 Boards

Issue 01 (2012-11-07)

Huawei Proprietary and Confidential

Summary of Contents for E8000E-X16























































































































































































Search results

Summary of Contents for E8000E-X16

Reviews:

Related manuals for E8000E-X16

Brands by name

Popular brands

Huawei E8000E-X16, Manual

Search results

Summary of Contents for E8000E-X16

Reviews:

Related manuals for E8000E-X16

Brands by name

Popular brands