Huawei E8000E-X16 Manual Download Page 105

Page: 105 / 182

Technical Specifications

Table 5-11

lists the technical specifications of the 20-port 100/1000Base-X-SFP flexible card.

Table 5-11

Technical specifications of the 20-port 100/1000Base-X-SFP flexible card

Item

Specifications

Silkscreen of the board name

P40-20xGE/FE-SFP

Power consumption (typical value)

37 W

Heat dissipation

120 BTU/hour

Board weight

0.6 kg

Dimensions (width x depth x height)

180 mm x 145 mm x 40 mm

Product Specifications

Table 5-12

lists the product specifications of the 20-port 100/1000Base-X-SFP flexible card.

Table 5-12

Product specifications of the 20-port 100/1000Base-X-SFP flexible card.

Item

Specifications

Supported protocol
and service

IEEE 802.3ab
IEEE 802.3z
IEEE 802.3x stream control
IEEE802.1q VLAN and Jumbo frames
IEEE802.3ad Link aggregation
IEEE 802.1p Label

Interface type

SFP

NMS

Enhanced command-line interface
SNMP and MIB support

Operating
conditions

Long-term ambient temperature: 0°C to 45°C
Short-term ambient temperature: -5°C to +55°C
Long-term relative humidity: 5% to 85%
Short-term relative humidity: 5% to 95%

Storage conditions

Storage temperature: -40°C to +70°C
Storage humidity: 0% to 95%

5.2.3 2-Port 10GBase LAN/WAN-XFP Flexible Card

HUAWEI Eudemon8000E Firewall
Hardware Description

5 Boards

Issue 01 (2012-11-07)

Huawei Proprietary and Confidential

Summary of Contents for E8000E-X16























































































































































































Search results

Summary of Contents for E8000E-X16

Reviews:

Related manuals for E8000E-X16

Brands by name

Popular brands

Huawei E8000E-X16, Manual

Search results

Summary of Contents for E8000E-X16

Reviews:

Related manuals for E8000E-X16

Brands by name

Popular brands