HP NetServer AA 4000 Installation Manual Download Page 71

Page: 71 / 82

Installing Windows and the Endurance Software

3-33

SplitSite Installation

To install in a SplitSite configuration, starting at the site of Tuple1:

If it is necessary to complete a single tuple installation before you begin the installation on the
second tuple, simply skip the step of installing IOP2 before installing the CE software.

Note:

The CE software is installed on only

one

CE. You can install the software on

either CE.

Step

Action

Install all software (Windows and Endurance) on IOP1

Use the Endurance Manager to disable CE1 and IOP1 (tuple 1)

Copy the Endurance configuration to a floppy disk.

Boot IOP1 in

Operational Endurance I/O Processor Mode.

Use the Endurance Manager to partition the CE boot disk on IOP1.

Power on CE1

Go to the site of Tuple 2

Install all software (Windows and Endurance) on IOP2.

Load the Endurance configuration file from the floppy you created on IOP1.

Correct the Ethernet addresses for the IOP2 redirected network card.

Use the Endurance Manager to enable IOP1.

Verify that IOP1 joins successfully, and correct any problems.

Use the Endurance Manager to disable IOP1.

Boot IOP2 in

Offline Endurance I/O Processor Mode

Install the CE software as described in this manual, replacing references to CE1 with CE2,
and IOP1 with IOP2.

Complete the CE software installation.

Use the Endurance Manager to enable IOP1.

Verify that IOP1 joins successfully.

Use the Endurance Manager to enable CE1.

Verify that CE1 synchronizes successfully.

Summary of Contents for NetServer AA 4000



















































































Search results

Summary of Contents for NetServer AA 4000

Reviews:

Related manuals for NetServer AA 4000

Brands by name

Popular brands

HP NetServer AA 4000, Installation Manual

Search results

Summary of Contents for NetServer AA 4000

Reviews:

Related manuals for NetServer AA 4000

Brands by name

Popular brands