HP NetServer AA 4000 Installation Manual Download Page 40

Page: 40 / 82

3-2

HP Netserver AA Solution Installation Guide

Overview of Endurance Installation

To complete an Endurance installation, you will follow this basic procedure:

IOPs

Install Windows on IOP1.

(page 3-4)

Complete the post
installation tasks.

(page 3-19)

Install Endurance software
on IOP1.

(page 3-8)

Configure the network
software.

(page 3-10)

Use the Endurance
Configuration Utility to
configure redirected
devices on IOP1.

(page 3-16)

Install Windows on IOP2.

(page 3-22)

Install Endurance software
on IOP2.

(page 3-8)

Configure the network
software.

(page 3-10)

Configure the devices on
IOP2 using the .cfg file
created on IOP1.

(page 3-16)

Complete the post
installation tasks.

(page 3-19)

Partition the CE disks.

(page 3-19)

Run MtcPrep to prepare for
the Unattended Installation.

(page 3-23)

Allow the Unattended
Installation of Windows and
the Endurance software to
complete.

(page 3-25)

Complete the Endurance
installation on the active
CE.

(page 3-28)

Join IOP1 and IOP2.

(page 3-22)

Install the appropriate
Service Pack.

(page 3-28)

Configure the network
software.

(page 3-29)

Adjust the Event Log
settings.

(page 3-31)

Partition and format the CE
disks.

(page 3-19)

Verify the Endurance
installation.

(page 3-31)

Summary of Contents for NetServer AA 4000



















































































Search results

Summary of Contents for NetServer AA 4000

Reviews:

Related manuals for NetServer AA 4000

Brands by name

Popular brands

HP NetServer AA 4000, Installation Manual

Search results

Summary of Contents for NetServer AA 4000

Reviews:

Related manuals for NetServer AA 4000

Brands by name

Popular brands