HP NetServer AA 4000 Installation Manual Download Page 62 | Manualshive

Page: 62 / 82

background image

3-24

HP Netserver AA Solution Installation Guide

To prepare for the Unattended Installation, follow these steps:

Step

Action

Notes

1

Using Endurance Manager, disable IOP2 and CE2.

You can use the Tuple Disable
Operation command for tuple 2.

2

If you have the Windows bootable CD in the
CD-ROM, remove it.

If you have the Windows CD in the
drive, when you boot the computer in
Step 3, the Windows setup starts.

3

Boot IOP1 in

Offline Endurance I/O Processor

Mode

.

The default is

Operational Endurance

I/O Processor Mode

. Be sure to select

Offline Endurance I/O Processor

Mode

.

4

On IOP1, launch

MtcPrep.exe.

MtcPrep.exe

creates files that

prepare the system for the Unattended
Installation of the Windows and
Endurance software on the CE.
The program is located in \Program
Files\Marathon Endurance\CE\Setup.
At this time, the information you provide
is accepted, and the preparation for the
installation proceeds.
However, if you entered an incorrect
Windows product key, later you will be
prompted for the correct one.

5

Specify the destination location for the CE’s copy of
the operating system.

• Drive: Browse to the drive you

marked as the boot disk in the
Endurance Configuration Utility.

• Folder: Indicate the Windows folder.

Typically this is

WINNT

.

6

Insert the Windows distribution media in the IOP
CD-ROM drive. On the Windows Distribution Media
screen, browse to the

\i386

folder.

The Windows installation directory
contains the setup utility

WINNT32.exe

, which copies the

Windows installation files to the CE boot
disk.

7

Answer all questions, providing information
applicable to your site, user, and operating system
licenses.

8

After you answer all questions, check

Begin CE

Windows installation now

to run the CE Windows

installation immediately

.

If the directory specified in Step 6 is not
correct, MtcPrep.exe cannot launch the
Unattended Installation setup correctly,
and an error appears on the screen.
In that case, verify the location of

WINNT32.exe

and run

MtcPrep.exe

again.

«
...
60
61
62
63
64
...
»

Summary of Contents for NetServer AA 4000



















































































Reviews:

No comments

Related manuals for NetServer AA 4000

NECCare Platinum Express5800/A1160

Brand: NEC Pages: 4

NECCare Gold Express5800/320Fd

Brand: NEC Pages: 11

NEC Express5800/R120d-2E

Brand: NEC Pages: 39

UNIVERGE NEAX 2000 IPS

Brand: NEC Pages: 244

UNIVERGE NEAX 2000 IPS

Brand: NEC Pages: 191

UNIVERGE NEAX 2000 IPS

Brand: NEC Pages: 96

Brand: BlueNet Video Pages: 38

Brand: Gigabyte Pages: 122

Brand: SmartSight Pages: 113

Brand: Synology Pages: 24

Brand: Hanwha Vision Pages: 16

Brand: EXAGATE Pages: 8

PRIMERGY RX2520 M4

Brand: Fujitsu Pages: 92

Primergy RX200 S4

Brand: Fujitsu Pages: 127

PRIMERGY RX200 S3

Brand: Fujitsu Pages: 100

PRIMERGY RX200 S6

Brand: Fujitsu Pages: 126

PRIMERGY RX2510 M2

Brand: Fujitsu Pages: 74

PRIMERGY RX200 S5

Brand: Fujitsu Pages: 72

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands