manualshive.com logo in svg

HP Jetdirect J7974E, Administrator'S Manual

Share
Download
HP Jetdirect J7974E Administrator'S Manual Download Page 44

If the list is empty, the print server does not send SNMP traps. The list may contain up to six entries. The default SNMP
Trap Destination List is empty. To receive SNMP traps, the systems listed on the SNMP trap destination list must have a
trap daemon to listen to those traps.

IPX/SPX

ipx-config:      (or ipx/spx:)

Enables or disables IPX/SPX protocol operation on the print server: 0 disables, 1 (default) enables.

ipx-unit-name:

A user-assigned alphanumeric name assigned to the print server (31 characters maximum). By default, the name will be
NPIxxxxxx, where xxxxxx are the last six digits of the LAN hardware address.

ipx-frametype:

Specify the IPX frame type setting available for your print server model: AUTO (default), EN_SNAP, EN_8022, EN_8023,
EN_II.

ipx-sapinterval:

Specifies the time interval (1 to 3600 seconds) that the HP Jetdirect print server waits between Service Advertising Protocol
(SAP) broadcasts on the network. The default is 60 seconds. 0 disables SAP broadcasts.

ipx-nds-tree:

Identifies the name of the Novell Directory Services (NDS) tree for this printer.

ipx-nds-context:

An alphanumeric string, up to 256 characters, that specifies the NDS context for the HP Jetdirect print server.

ipx-job-poll:

Specifies the time interval (seconds) that the HP Jetdirect print server will wait to check for print jobs in a print queue.

pjl-banner:      (or ipx-banner:)

Enables or disables printing an IPX banner page. 0 disables banner pages. 1 (default) enables banner pages.

pjl-eoj:      (or ipx-eoj:)

Enables or disables IPX end-of-job notification. 0 disables, 1 (default) enables.

pjl-toner-low:      (or ipx-toner-low:)

Enables or disables IPX toner-low notification. 0 disables, 1 (default) enables.

AppleTalk

appletalk:      (or at-config:, ethertalk:)

Enables or disables AppleTalk (EtherTalk) protocol operation on the print server: 0 disables, 1 (default) enables.

DLC/LLC

dlc/llc-config:      (or dlc/llc:)

Enables or disables DLC/LLC protocol operation on the print server: 0 disables, 1 (default) enables.

Other Settings

link-type:

(For wired 10/100/1000T Ethernet) Sets the print server's link speed (10, 100, 1000 Mbps) and communication mode (Full-
or Half-Duplex). The available link-speed selections depend on the print server model. Selections are AUTO, 1000FULL,
100AUTO, 100FULL, 100HALF, 10FULL, 10HALF.

Table 3-2

  TFTP Configuration File Parameters (continued)

34

Chapter 3   TCP/IP Configuration

ENWW

Summary of Contents for Jetdirect J7974E



























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands