HP 64780A User Manual Download Page 255 | Manualshive

Page: 255 / 546

background image

Initialization with User Defined Ranges

You can specifically give the SPMT address ranges to use by placing the
information in a file and entering the file name in the
performance_measurement_initialize command.

Address range files may contain program symbols (procedure name or static), user
defined address ranges, and comments. An example address range file is shown
below.

# Any line which starts with a # is a comment.
# All user’s labels must be preceded by a "|".

|users_label 10H 1000H
program_symbol

# A program symbol can be a procedure name or a static. In the case of a pro-
# cedure name the range of that procedure will be used.

|users_label2 program_symbol1 -> program_symbol2

# "->" means thru. The above will define a range which starts with symbol1
# and goes thru symbol2. If both symbols are procedures then the range will
# be defined as the start of symbol1 thru the end of symbol2.

dir1/dir2/source_file.s:local_symbol

# The above defines a range based on the address of local_symbol.

Initialization with Global Symbols

When the performance_measurement_initialize command is entered with no
options or with the global_symbols option, the global symbols in the symbols
database become the address ranges for which activity is measured. If the symbols
database is not loaded, a default set of ranges that cover the entire processor
address range will be used.

The global symbols database contains procedure symbols, which are associated
with the address range from the beginning of the procedure to the end, and static
symbols, which are associated with the address of the static variable.

Initialization with Local Symbols

When the performance_measurement_initialize command is entered with the
local_symbols_in option and a source file name, the symbols associated with that
source file become the address ranges for which activity is measured. If the
symbols database is not loaded, an error message will occur telling you that the
source filename symbol was not found.

Chapter 8: Making Software Performance Measurements

Activity Performance Measurements

235

«
...
253
254
255
256
257
...
»

Summary of Contents for 64780A



































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 64780A

Brand: E Instruments Pages: 2

Brand: ICM Controls Pages: 8

Wind Monitor Series

Brand: Campbell Pages: 38

Brand: Favero Electronics Pages: 12

Brand: TASKING Pages: 12

Brand: S.E. International Pages: 30

Brand: SZBJ Pages: 2

Brand: Motortech Pages: 142

Brand: Environmental Express Pages: 40

OPTIFLUX 4040 C Series

Brand: KROHNE Pages: 20

Brand: Badger Meter Pages: 24

Brand: HBM Pages: 84

Brand: Bogen Pages: 14

Brand: Kurzweil Pages: 12

Brand: Eurotron Pages: 122

Brand: CryptOn Pages: 13

QI-POWER-485-300-LV

Brand: QEED Pages: 2

Brand: Ocean Reef Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands