HP 5800 Command Reference Manual Download Page 88

Page: 88 / 396

•

regular-expression

: Specifies a regular expression, which is a case-sensitive string of 1 to 256

characters.

Examples

# Display the usage information of the specified NHLFE entry.

<Sysname> display mpls nhlfe reflist 11

No. Type Key-Info

-------------------------------------------------------------

1 ILM 1023(Inlabel) Vlan10(In-If)

2 FTN 1(VPN ID) 2.2.2.2/32

3 LPW ----(SRV ID) Vlan20(Private-If)

4 VPW 1(VSI ID) 1(Link ID)

5 FRR 11(Token) ----

Table 37

Command output

Field Description

Total interface node

Total number of associated nodes

Type

Type of the associated node

Key-Info

Key parameters of the entry

NOTE:

An asterisk (*) before the number of a node entry means that the node is invalid and is to be deleted.

Table 38

Types of associated nodes and their key parameters

Node type

Description

Key parameter

FTN

FEC to NHLFE mapping

•

VPN ID: VPN instance ID

•

Address prefix/mask

ILM

Incoming label mapping

•

In-Label: Incoming label

•

In-If: Incoming interface

LPW

Sending entries of VPWS PW

•

SRV ID: Service instance ID

•

Private-If: Private network interface

VPW

Sending entries of VPLS PW

•

VSI ID: Virtual switching instance
ID

•

Link ID: Link ID

FRR

Primary NHLFE of FRR

Token: Token of the primary NHLFE

BFD

Check the connectivity of the NHLFE
through BFD

BFD Discr: Local discriminator value of
the BFD session

display mpls route-state

Description

Use the

display mpls route-state

command to display the LSP information of routes.

With no VPN instance specified, the command displays the LSP information of the routes of the public

network instance.

Summary of Contents for 5800













































































































































































































































































































































































































Search results

Summary of Contents for 5800

Reviews:

Brands by name

Popular brands

HP 5800, Command Reference Manual

Search results

Summary of Contents for 5800

Reviews:

Brands by name

Popular brands