HP 5800 Command Reference Manual Download Page 265

Page: 265 / 396

256

exclude

: Displays all lines that do not match the specified regular expression.

include

: Displays all lines that match the specified regular expression.

regular-expression

: Specifies a regular expression, which is a case-sensitive string of 1 to 256 characters.

Examples

# Display information about all static VCs configured on the router.

<Sysname> display mpls static-l2vc

total connections: 1, 1 up, 0 down

ce-intf state destination tr-label rcv-label tnl-policy

Vlan2 up 3.3.3.9 100 200 policy1

Table 111

Command output

Field Description

total connections

Statistics about connection, including the total
number of connections, number of connections that

are up, and number of connections that are down

ce-intfe CE

interface

State

Status of the VC

destination

Destination IP address

tr-label Outgoing

label

rcv-label Incoming

label

tnl-policy

Name of the tunneling policy

# Display information about static VCs configured on interface Vlan-interface 2.

<Sysname> display mpls static-l2vc interface vlan-interface 2

***CE-interface : Vlan-interface2 is up

VC State : up

Destination : 3.3.3.9

Transmit-vpn-label : 100

Receive-vpn-label : 400

Tunnel Policy : policy1

Tunnel Type : lsp

Tunnel ID : 0x226013

Table 112

Command output

Field Description

CE-interface

Name of the CE interface

VC State

Status of the VC

Destination

Destination IP address

Transmit-vpn-label Outgoing

label

Receive-vpn-label Incoming

label

Tunnel Policy

Name of the tunneling policy

Tunnel Type

Type of the tunnel

Summary of Contents for 5800













































































































































































































































































































































































































Search results

Summary of Contents for 5800

Reviews:

Brands by name

Popular brands

HP 5800, Command Reference Manual

Search results

Summary of Contents for 5800

Reviews:

Brands by name

Popular brands