HP 5800 Command Reference Manual Download Page 356

Page: 356 / 396

347

Local AS number : 200

Total number of peers : 1 Peers in established state : 0

Peer AS MsgRcvd MsgSent OutQ PrefRcv Up/Down State

192.168.1.40 100 0 0 0 0 00:02:10 Active

Table 135

Command output

Field Description

Peer

IP address of the peer

AS number of the peer

MsgRcvd

Number of messages received

MsgSent

Number of messages sent

OutQ

Number of messages to be sent to the peer

PrefRcv

Number of prefixes received

Up/Down

Duration of the BGP session in the current state

State

Current state of the peer

# Display the detailed information of the BGP VPNv6 peer 1.1.1.1.

<Sysname> display bgp vpnv6 all peer 1.1.1.1 verbose

Peer: 1.1.1.1 Local: 2.2.2.2

Type: IBGP link

BGP version 4, remote router ID 1.1.1.1

BGP current state: Established, Up for 00h46m01s

BGP current event: RecvKeepalive

BGP last state: OpenConfirm

Port: Local - 1039 Remote - 179

Configured: Active Hold Time: 180 sec Keepalive Time:60 sec

Received : Active Hold Time: 180 sec

Negotiated: Active Hold Time: 180 sec

Peer optional capabilities:

Peer support bgp multi-protocol extended

Peer support bgp route refresh capability

Address family IPv4 Unicast: advertised and received

Address family VPNv6: advertised and received

Received: Total 52 messages, Update messages 2

Sent: Total 65 messages, Update messages 5

Maximum allowed prefix number: 150000

Threshold: 75%

Minimum time between advertisement runs is 15 seconds

Optional capabilities:

ORF advertise capability based on Prefix(type 64):

Local: both

Negotiated: send

Summary of Contents for 5800













































































































































































































































































































































































































Search results

Summary of Contents for 5800

Reviews:

Brands by name

Popular brands

HP 5800, Command Reference Manual

Search results

Summary of Contents for 5800

Reviews:

Brands by name

Popular brands