HP 5800 Command Reference Manual Download Page 74

Page: 74 / 396

Table 26

Command output

Field Description

Peer-ID

LDP identifier of the peer. See

Table 24

for detailed

description of LDP ID.

Discovery-Source Interface

that discovers the peer.

# Display detailed information about all peers.

<Sysname> display mpls ldp peer verbose

LDP Peer Information in Public network

---------------------------------------------------------------

Peer LDP ID : 172.17.1.2:0

Peer Max PDU Length : 4096 Peer Transport Address : 172.17.1.2

Peer Loop Detection : Off Peer Path Vector Limit : 0

Peer FT Flag : Off Peer Keepalive Timer : 45 Sec

Recovery Timer : ---- Reconnect Timer : ----

Peer Label Advertisement Mode : Downstream Unsolicited

Peer Discovery Source : Vlan-interface1

------------------------------------------------------------

Peer LDP ID : 168.1.1.1:0

Peer Max PDU Length : 4096 Peer Transport Address : 168.1.1.1

Peer Loop Detection : Off Peer Path Vector Limit : 0

Peer FT Flag : Off Peer Keepalive Timer : 45 Sec

Recovery Timer : ---- Reconnect Timer : ----

Peer Label Advertisement Mode : Downstream Unsolicited

Peer Discovery Source : Vlan-interface2

-------------------------------------------------------------

Peer LDP ID : 100.10.1.1:0

Peer Max PDU Length : 4096 Peer Transport Address : 100.10.1.1

Peer Loop Detection : Off Peer Path Vector Limit : 0

Peer FT Flag : Off Peer Keepalive Timer : 45 Sec

Recovery Timer : ---- Reconnect Timer : ----

Peer Label Advertisement Mode : Downstream Unsolicited

Peer Discovery Source : Vlan-interface3

------------------------------------------------------------

Table 27

Command output

Field Description

Peer LDP ID

LDP identifier of the peer. See

Table 24

for detailed

description of LDP ID.

Peer FT Flag

Whether the GR FT function is enabled.

Peer Discovery Source

Interface that discovers the peer.

Summary of Contents for 5800













































































































































































































































































































































































































Search results

Summary of Contents for 5800

Reviews:

Brands by name

Popular brands

HP 5800, Command Reference Manual

Search results

Summary of Contents for 5800

Reviews:

Brands by name

Popular brands