HP 5800 Command Reference Manual Download Page 31

Page: 31 / 396

Syntax

ip binding vpn-instance

vpn-instance-name

undo ip binding vpn-instance

vpn-instance-name

View

VLAN interface view, Tunnel interface view, Layer 3 Ethernet interface

Default level

2: System level

Parameters

vpn-instance-name

: Specifies the name of the VPN instance to be associated, which is a case-insensitive

string of 1 to 31 characters.

Examples

# Associate VLAN-interface 1 with the VPN instance

vpn1

<Sysname> system-view

[Sysname] interface Vlan-interface1

[Sysname-Vlan-interface1] ip binding vpn-instance vpn1

# Associate Tunnel 0 with the VPN instance

vpn2.

<Sysname> system-view

[Sysname] interface Tunnel 0

[Sysname-Tunnel0] ip binding vpn-instance vpn2

# Associate the management Ethernet interface with the VPN instance

vpn3

<Sysname> system-view

[Sysname] interface M-GigabitEthernet 0/0/0

[Sysname-M-Ethernet0/0/0] ip binding vpn-instance vpn3

ip vpn-instance

Description

Use the

ip vpn-instance

command to create a VPN instance and enter VPN instance view.

Use the

undo ip vpn-instance

command to delete a VPN instance.

A VPN instance takes effect only after you configure an RD for it.
Related command:

route-distinguisher

Syntax

ip vpn-instance

vpn-instance-name

undo ip vpn-instance

vpn-instance-name

View

System view

Default level

2: System level

Summary of Contents for 5800













































































































































































































































































































































































































Search results

Summary of Contents for 5800

Reviews:

Brands by name

Popular brands

HP 5800, Command Reference Manual

Search results

Summary of Contents for 5800

Reviews:

Brands by name

Popular brands