HP 5800 Command Reference Manual Download Page 272

Page: 272 / 396

263

View

Any view

Default level

0: Visit level

Parameters

-a

source-ip

: Specifies the source IP address of the Echo Request messages to be sent.

-c

count

: Specifies the number of request messages to be sent. The

count

parameter ranges from 1 to

4,294,967,295 and defaults to 5.

-exp

exp-value

: Specifies the EXP value for the Echo Request messages. The

exp-value

parameter ranges

from 0 to 7 and defaults to 0.

-h

ttl-value

: Specifies the TTL value for the Echo Request messages. The

ttl-value

parameter ranges from 1

to 255 and defaults to 255.

-m

wait-time

: Specifies the interval for sending Echo Request messages. The

wait-time

parameter ranges

from 1 to 10,000 and defaults to 200, in milliseconds.

-r

reply-mode

: Specifies the reply mode of a receiver in response to an Echo Request message. The

reply-

mode

parameter can be 1 or 2 where 1 means “Do not respond” and 2 means “Respond using a UDP

packet.” The default is 2.

-s

packet-size

: Specifies the payload length of the Echo Request messages. The

packet-size

parameter

ranges from 65 to 8100 and defaults to 100, in bytes.

-t

time-out

: Specifies the timeout interval for waiting for the response to an echo request message. The

time-out

parameter ranges from 0 to 65,535 and defaults to 2000, in milliseconds.

-v

: Displays detailed response information.

ip-address

: Specifies the IP address of the peer PE.

pw-id

pw-id

: Specifies the ID of the PW to the peer PE. The

pw-id

parameter ranges from 1 to

4,294,967,295.

Examples

# Check the validity and reachability of the VC that is with PW ID 301 and connected to peer PE 3.3.3.9.

<Sysname> ping lsp pw 3.3.3.9 pw-id 301

LSP Ping FEC: FEC 128 PSEUDOWIRE (NEW) 3.3.3.9 301 : 100 data bytes, press CTRL_C to

break

Reply from 100.1.2.1: bytes=100 Sequence=0 time = 31 ms

Reply from 100.1.2.1: bytes=100 Sequence=1 time = 62 ms

Reply from 100.1.2.1: bytes=100 Sequence=2 time = 62 ms

Reply from 100.1.2.1: bytes=100 Sequence=3 time = 62 ms

Reply from 100.1.2.1: bytes=100 Sequence=4 time = 62 ms

--- FEC: FEC 128 PSEUDOWIRE (NEW) 3.3.3.9 301 ping statistics ---

5 packet(s) transmitted

5 packet(s) received

0.00% packet loss

round-trip min/avg/max = 31/55/62 ms

Summary of Contents for 5800













































































































































































































































































































































































































Search results

Summary of Contents for 5800

Reviews:

Brands by name

Popular brands

HP 5800, Command Reference Manual

Search results

Summary of Contents for 5800

Reviews:

Brands by name

Popular brands