HP 5800 Command Reference Manual Download Page 66

Page: 66 / 396

: Filters command output by specifying a regular expression. For more information about regular

expressions, see the

Fundamentals Configuration Guide

•

begin

: Displays the first line that matches the specified regular expression and all lines that follow.

•

exclude

: Displays all lines that do not match the specified regular expression.

•

include

: Displays all lines that match the specified regular expression.

•

regular-expression

: Specifies a regular expression, which is a case-sensitive string of 1 to 80

characters.

Examples

# Display all information about LDP in detail.

<Sysname> display mpls ldp all verbose

LDP Global Information

---------------------------------------------------------------

Protocol Version : V1 Neighbor Liveness : 60 Sec

Graceful Restart : Off FT Reconnect Timer : 60 Sec

MTU Signaling : Off Recovery Timer : 60 Sec

LDP Instance Information

---------------------------------------------------------------

Instance ID : 0 VPN-Instance :

Instance Status : Active LSR ID : 1.1.1.1

Hop Count Limit : 32 Path Vector Limit : 32

Loop Detection : Off

DU Re-advertise Timer : 30 Sec DU Re-advertise Flag : On

DU Explicit Request : Off Request Retry Flag : On

Label Distribution Mode: Ordered Label Retention Mode : Liberal

-----------------------------------------------------------------

Table 22

Command output

Field Description

Protocol Version

Version of the LDP protocol.

Neighbor Liveness

Setting of the GR neighbor liveness timer.

Graceful Restart

Whether GR is enabled.

FT Reconnect Timer

Setting of the GR’s FT reconnect timer.

MTU Signaling

Whether MTU signaling is supported. The device
does not support MTU signaling.

Recovery Timer

Setting of the GR’s recovery timer.

Instance ID

Sequence number of the LDP instance.

VPN-Instance

Name of the LDP-enabled VPN instance. For the
default instance, nothing is displayed.

Hop Count Limit

Maximum hop count for loop detection.

Path Vector Limit

Maximum path vector length.

Loop Detection

Whether loop detection is enabled.

DU Re-advertise Timer

Label re-advertisement interval for DU mode.

Summary of Contents for 5800













































































































































































































































































































































































































Search results

Summary of Contents for 5800

Reviews:

Brands by name

Popular brands

HP 5800, Command Reference Manual

Search results

Summary of Contents for 5800

Reviews:

Brands by name

Popular brands